Woods 60"-84" Severe Duty Rear 3ph Blade Rubber Edge Kit for RBS60P, RBS72P, and RBS84P
Includes FREE Ground Shipping in the lower 48 states in the USA
Our Severe Duty Kit is the most durable, corrosion resistant, optimal snow clearing plow edge kit for high volume plowing needs. Also, specifically intended for those who have a need to use extensive snow melt products to keep the pavement clear for Medical Centers, Municipal Buildings, etc.
If your plowing needs are extreme, this kit is the answer to your needs. It' turns your rear Woods 3ph Blade into a snow clearing implement suited for extreme use. Plow hard, Plow often and Plow in tough conditions where there is highly corrosive environment, this is the kit you need.
This kit was purpose designed and created to take these difficult tasks head on, which include
Very frequent plowing use, even multi times daily during the season.
The need to adjust the plow edges to always get the maximum result.
Uneven pavement surfaces, including potholes, surface cracks and pavement at various heights.
Very difficult to clean surface due to previous wear, damage, etc.
Consider this Woods Plow Kit if your plow meets these descriptions
The plow has a "P" after the plow size in the Model Number
If the plow allows for center blade offset up to 12" left or right
Allows blade tilt up to 15 degrees from vertical
Has Adjustable Plow Shoes, Plow End Caps on the Moldboard
How will you know for sure, if your Woods 3ph Rear Blade is a Standard Blade or a Premium Series Plow Blade?
The Premium Woods 3ph plow offers the ability to Offset the blade in the center, adjusting the blade offset by 12" left or right of center on these blades.
Premium Woods 3ph rear blades have adjustable plow shoes where the standard Woods Plow's shoes are not adjustable. In fact, many of the base plows don't have any plow shoes
This kit turns your Woods 3ph blade into a snow clearing implement which is quiet, doesn't harm the surface and cleans the snow far better than the steel wear edge being replaced.
Our Severe Duty Blade Rubber Edge Kit includes the following
Custom laser cut, double sided rubber plow edge material to provide extraordinary snow clearing results. The rubber plow edge height is between 6" and 8" tall and between 3/4" and 1" thick, based upon the plow's width, weight and intended use.
Wider plow blades will have thicker and taller rubber wear edges due to the plows greater weight. The rubber edge is produced to permit adjustment as used to make sure to provide the optimal clearing results.
You can choose between a double sided rubber wear edge which will permit you to flip the rubber edge as it wears. For those with real snow clearing challenges, such as very rough pavement or surfaces with very uneven surfaces due to pavement degradation, we offer the Double Edge, Double Layered rubber edges, for the highest level of pavement surface cleaning. The actual sizes of this material will depend upon the plow width, but it's going to be have a cleaning edge of no less than 1".
On some plow's we have created Multi Layer Edges which are 2" thick on the clearing edge, when the plows are large and heavy enough. Our goal is to provide your plow the best possible snow clearing edge on the market.
The strap which we custom cut to fit your plow, is made from UHMW and it's thickness is based upon the plow's width and operating weight due to the snow clearing loads. The UHMW straps will be as much as 4x thicker than it's steel counterparts.
Also those plows with double sided, double Layered rubber edges will custom made UHMW straps up to 1" thick. The thickness of the UHMW strap will be tied to the load on the plow's layered rubber edges.
Easy to install due to the precision fabrication. Simply remove the plow's steel plow edge and all hardware and set it aside. Install our new rubber edge and the metal strap and follow the installation instructions and you will find dramatically improved plow function and snow clearing results.
Our Double edge kit is designed for optimal clearing results and the longest useful life of the wear edge. If you are looking for the most durable, longest lasting and best clearing kit for your Woods Premium Series Plow, our Extreme Duty Edge and Installation kit is the answer.
All Stainless Steel Hardware, assures the plow edges can be adjusted, flipped and turned to achieve maximum use of all edges and straps.
The Stainless Hardware is very expensive when the hardware is larger than 1/2" in diameter. In fact a single Stainless bolt costs more than the entire hardware kit for a basic level plow edge kit with a corrosive resistant hardware.,
But there are few things more frustrating than breaking bolts and having to cut apart edge kits from plows, especially those which are frequently in corrosive conditions. That's why our entire Severe Duty Kit is made from UHMW, Specialized Rubber and Stainless Hardware. Our kit solves these problems, by eliminating them from the inception.
Includes FREE Ground Shipping in the lower 48 states in the USA
Our Severe Duty Kit is the most durable, corrosion resistant, optimal snow clearing plow edge kit for high volume plowing needs. Also, specifically intended for those who have a need to use extensive snow melt products to keep the pavement clear for Medical Centers, Municipal Buildings, etc.
If your plowing needs are extreme, this kit is the answer to your needs. It' turns your rear Woods 3ph Blade into a snow clearing implement suited for extreme use. Plow hard, Plow often and Plow in tough conditions where there is highly corrosive environment, this is the kit you need.
This kit was purpose designed and created to take these difficult tasks head on, which include
Very frequent plowing use, even multi times daily during the season.
The need to adjust the plow edges to always get the maximum result.
Uneven pavement surfaces, including potholes, surface cracks and pavement at various heights.
Very difficult to clean surface due to previous wear, damage, etc.
Consider this Woods Plow Kit if your plow meets these descriptions
The plow has a "P" after the plow size in the Model Number
If the plow allows for center blade offset up to 12" left or right
Allows blade tilt up to 15 degrees from vertical
Has Adjustable Plow Shoes, Plow End Caps on the Moldboard
How will you know for sure, if your Woods 3ph Rear Blade is a Standard Blade or a Premium Series Plow Blade?
The Premium Woods 3ph plow offers the ability to Offset the blade in the center, adjusting the blade offset by 12" left or right of center on these blades.
Premium Woods 3ph rear blades have adjustable plow shoes where the standard Woods Plow's shoes are not adjustable. In fact, many of the base plows don't have any plow shoes
This kit turns your Woods 3ph blade into a snow clearing implement which is quiet, doesn't harm the surface and cleans the snow far better than the steel wear edge being replaced.
Our Severe Duty Blade Rubber Edge Kit includes the following
Custom laser cut, double sided rubber plow edge material to provide extraordinary snow clearing results. The rubber plow edge height is between 6" and 8" tall and between 3/4" and 1" thick, based upon the plow's width, weight and intended use.
Wider plow blades will have thicker and taller rubber wear edges due to the plows greater weight. The rubber edge is produced to permit adjustment as used to make sure to provide the optimal clearing results.
You can choose between a double sided rubber wear edge which will permit you to flip the rubber edge as it wears. For those with real snow clearing challenges, such as very rough pavement or surfaces with very uneven surfaces due to pavement degradation, we offer the Double Edge, Double Layered rubber edges, for the highest level of pavement surface cleaning. The actual sizes of this material will depend upon the plow width, but it's going to be have a cleaning edge of no less than 1".
On some plow's we have created Multi Layer Edges which are 2" thick on the clearing edge, when the plows are large and heavy enough. Our goal is to provide your plow the best possible snow clearing edge on the market.
The strap which we custom cut to fit your plow, is made from UHMW and it's thickness is based upon the plow's width and operating weight due to the snow clearing loads. The UHMW straps will be as much as 4x thicker than it's steel counterparts.
Also those plows with double sided, double Layered rubber edges will custom made UHMW straps up to 1" thick. The thickness of the UHMW strap will be tied to the load on the plow's layered rubber edges.
Easy to install due to the precision fabrication. Simply remove the plow's steel plow edge and all hardware and set it aside. Install our new rubber edge and the metal strap and follow the installation instructions and you will find dramatically improved plow function and snow clearing results.
Our Double edge kit is designed for optimal clearing results and the longest useful life of the wear edge. If you are looking for the most durable, longest lasting and best clearing kit for your Woods Premium Series Plow, our Extreme Duty Edge and Installation kit is the answer.
All Stainless Steel Hardware, assures the plow edges can be adjusted, flipped and turned to achieve maximum use of all edges and straps.
The Stainless Hardware is very expensive when the hardware is larger than 1/2" in diameter. In fact a single Stainless bolt costs more than the entire hardware kit for a basic level plow edge kit with a corrosive resistant hardware.,
But there are few things more frustrating than breaking bolts and having to cut apart edge kits from plows, especially those which are frequently in corrosive conditions. That's why our entire Severe Duty Kit is made from UHMW, Specialized Rubber and Stainless Hardware. Our kit solves these problems, by eliminating them from the inception.
Includes FREE Ground Shipping in the lower 48 states in the USA
Our Severe Duty Kit is the most durable, corrosion resistant, optimal snow clearing plow edge kit for high volume plowing needs. Also, specifically intended for those who have a need to use extensive snow melt products to keep the pavement clear for Medical Centers, Municipal Buildings, etc.
If your plowing needs are extreme, this kit is the answer to your needs. It' turns your rear Woods 3ph Blade into a snow clearing implement suited for extreme use. Plow hard, Plow often and Plow in tough conditions where there is highly corrosive environment, this is the kit you need.
This kit was purpose designed and created to take these difficult tasks head on, which include
Very frequent plowing use, even multi times daily during the season.
The need to adjust the plow edges to always get the maximum result.
Uneven pavement surfaces, including potholes, surface cracks and pavement at various heights.
Very difficult to clean surface due to previous wear, damage, etc.
Consider this Woods Plow Kit if your plow meets these descriptions
The plow has a "P" after the plow size in the Model Number
If the plow allows for center blade offset up to 12" left or right
Allows blade tilt up to 15 degrees from vertical
Has Adjustable Plow Shoes, Plow End Caps on the Moldboard
How will you know for sure, if your Woods 3ph Rear Blade is a Standard Blade or a Premium Series Plow Blade?
The Premium Woods 3ph plow offers the ability to Offset the blade in the center, adjusting the blade offset by 12" left or right of center on these blades.
Premium Woods 3ph rear blades have adjustable plow shoes where the standard Woods Plow's shoes are not adjustable. In fact, many of the base plows don't have any plow shoes
This kit turns your Woods 3ph blade into a snow clearing implement which is quiet, doesn't harm the surface and cleans the snow far better than the steel wear edge being replaced.
Our Severe Duty Blade Rubber Edge Kit includes the following
Custom laser cut, double sided rubber plow edge material to provide extraordinary snow clearing results. The rubber plow edge height is between 6" and 8" tall and between 3/4" and 1" thick, based upon the plow's width, weight and intended use.
Wider plow blades will have thicker and taller rubber wear edges due to the plows greater weight. The rubber edge is produced to permit adjustment as used to make sure to provide the optimal clearing results.
You can choose between a double sided rubber wear edge which will permit you to flip the rubber edge as it wears. For those with real snow clearing challenges, such as very rough pavement or surfaces with very uneven surfaces due to pavement degradation, we offer the Double Edge, Double Layered rubber edges, for the highest level of pavement surface cleaning. The actual sizes of this material will depend upon the plow width, but it's going to be have a cleaning edge of no less than 1".
On some plow's we have created Multi Layer Edges which are 2" thick on the clearing edge, when the plows are large and heavy enough. Our goal is to provide your plow the best possible snow clearing edge on the market.
The strap which we custom cut to fit your plow, is made from UHMW and it's thickness is based upon the plow's width and operating weight due to the snow clearing loads. The UHMW straps will be as much as 4x thicker than it's steel counterparts.
Also those plows with double sided, double Layered rubber edges will custom made UHMW straps up to 1" thick. The thickness of the UHMW strap will be tied to the load on the plow's layered rubber edges.
Easy to install due to the precision fabrication. Simply remove the plow's steel plow edge and all hardware and set it aside. Install our new rubber edge and the metal strap and follow the installation instructions and you will find dramatically improved plow function and snow clearing results.
Our Double edge kit is designed for optimal clearing results and the longest useful life of the wear edge. If you are looking for the most durable, longest lasting and best clearing kit for your Woods Premium Series Plow, our Extreme Duty Edge and Installation kit is the answer.
All Stainless Steel Hardware, assures the plow edges can be adjusted, flipped and turned to achieve maximum use of all edges and straps.
The Stainless Hardware is very expensive when the hardware is larger than 1/2" in diameter. In fact a single Stainless bolt costs more than the entire hardware kit for a basic level plow edge kit with a corrosive resistant hardware.,
But there are few things more frustrating than breaking bolts and having to cut apart edge kits from plows, especially those which are frequently in corrosive conditions. That's why our entire Severe Duty Kit is made from UHMW, Specialized Rubber and Stainless Hardware. Our kit solves these problems, by eliminating them from the inception.
Due to the number of product variables, these kits are often produced with ordered. Please allow us 14 business days to produce and ship your purchase. We will advise you of the shipping day and provide tracking numbers for your use. Thank you for your interest in our kits.