Frontier AS10H Snow Pushers Rubber Edge and UHMW Shoe Kit
Includes FREE Ground Shipping in the Lower 48 States
If you have the Frontier brand, Front End Loader Mounted Snow Pusher, Model AS10H this listing is for the rubber wear edge on the pushers. Our Rubber Edge is a replacement to the rubber edge which came in the pusher when new.
This pusher is made in the 72” width, 84” width and the 96” width. Our rubber edge replaces the original rubber wear edge on the back of the snow pusher.
The rubber edge is professionally machined with vertical adjustment slots to perfectly align with the mounting holes on the pushers cutting edge location.
This precise machining provides for an easy replacement of the worn main rubber wear edge, to assure the installation, periodic adjustment and ultimate flipping over of the rubber edge is trouble free, to extend the edges useful wear life.
Provides double the wear life by being two sided so it can be flipped over for an entirely new wear edge on the other side.
Contains a full set of corrosion resistant mounting hardware, which are the carriage bolts, the flat washers and the locking nuts to make the installation much easier.
The corrosion resistant hardware makes the periodic adjustments as well as the reversing and flipping over of the main rubber edge easier to complete during use.
Installation Instructions.
The following are the listed weights for the rubber edge which Deere sells for this snow pusher’
72” x 8” x 1” main rubber wear edge weighs 19 pounds
84” x 8” x 1” main rubber wear edge weighs 23 pounds
96” x 8” x 1” main rubber wear edge weighs 26 pounds
Look at how our SBS, LLC plow rubber of the same width and same thickness compares to the Deere Rubber plow edge
72” x 8” x 1” SBS Plow Rubber edge weighs 35 pounds(+16 pounds)
84” x 8” x 1” SBS Plow Rubber Edge weighs 40 pounds(+17 pounds)
96” × 8” x1” SBS Plow Rubber Edge weighs 45 pounds(+19 pounds)
Guess which edge will last longer and work better? Yes, the rubber edge which is more dense, has more mass and greater wear duration and which weighs nearly 50% more. Our Rubber edge.
Now, lets look at the cost difference for the same rubber. We will provide you the Deere part numbers, so you can double check if you like to verify the cost information.
72” Plow Rubber, Deere 5FP1352539, $ 447.75 SBS Price $ 385
84” Plow Rubber, Deere 5FP1352538, $ 566.48 SBS Price $ 485
96” Plow Rubber, Deere 5FP1352467, $ 688.64 SBS Price $ 585
This makes the decision.
Our SBS Snow Pusher Rubber Weighs more (a lot more) so it will last longer. And it costs less, a lot less. Plus our Rubber wear edge includes all new Corrosion Resistant hardware to install the edge, Deere’s is sold at an extra cost. Why pay more and get less?
If you do want to change from the Rubber edge on the snow pusher to a UHMW wear edge, we make that as well. That’s a choice which Deere Doesn’t offer……
We use a very dense rubber product for our plow edges, which we have used for years. Our plow edge wears very well and lasts a long time and cleans the pavement very nicely. In fact, its the best plow rubber material we have found.
Our Rubber edges Ship with a complete set of Corrosion Resistant Hardware, to make installation easy so you aren’t dealing with using old bolts. Our hardware is included in our price, as is our Ground Delivery shipping.
Precision machined for perfect fit, high grade rubber for extended wear life, this back drag rubber restores the function of your snow pushers back drag arm to like new.
Rubber Wear Edge Mounting Straps are available.
We also make the mounting strap to secure the rubber edge, if your metal strap is rusty, damaged, etc. Just make sure to add the strap option to your order to fit the size of your plow blade.
Upgrade to a UHMW Wear Bar and Scrape Hard pack and Ice
If your snow clearing with your AS10H Snow pusher finds you dealing with hard packed snow and ice, you should consider replacing that rubber edge with the UHMW edge. Will scrap like steel, without the noise or abrasion damage. The UHMW wear edges, when used correctly, will last as long or longer than the Mild Steel Option which normally ships on the snow pushers.
The UHMW is often said “Wears like steel, without damage, noise and problems”. The UHMW wear edge won’t harm the pavement. If you need some more “bite” in your snow clearing, but don’t want to destroy the surface in the process. UHMW is your answer.
Our UHMW edge is 1.25” thick and 8” tall. It’s the width of your plow at either 72”, 84” or 96”. We ship our new UHMW wear edges fully cut on the water jet and ready to install with our vertical mounting slots and the edge is cut to length. Don’t buy a project you need to cut and drill to make it fit. Get an edge professionally machined and ready to install in a matter of minutes. Our UHMW Edge includes our Corrosion Resistant Hardware set to complete the installation.
Installation Time Estimates
To replace the rubber wear edge in the snow pusher typically takes 20 to 30 minutes. Installing our new edge is easier thanks to the new hardware as well as the manner in which we machine the installation slots in the rubber edge. Whether installing our new Rubber Replacement edge or our UHMW wear edge, expect the total time to be between 20 and 45 minutes in total. Make sure to follow all safety precautions. Remember, these are only estimates and work conditions, tools, mechanical skill and other factors all impact these results.
Replace those Steel Shoes damaging your driveway pavement
One last item for your consideration. If you would like to end the surface abrasion of the steel shoes on the Deere AS10H snow pusher, we make a complete set of UHMW Shoes for the Deere Snow pusher.
Our new snow pusher UHMW shoes require the removal of the existing shoes. You would have to remove the steel shoes on your pusher, which are going to have to be cut off the pusher housing with either a cutting wheel, plasma cutter or 90 degree grinder. Once the steel shoes are removed, the new shoes install easily on the ends of the snow pusher housing.
Our new shoes are UHMW and include everything needed to install the UHMW shoes, which won’t damage your driveway or pavement. You may find that there are those who want to purchase your old snow pusher steel shoes to attach to box blades or other such assemblies. Keep that in mind when cutting them off the pusher as they may have value to partially help offset the cost of the new items.
You get the old pusher shoes off the pusher, and
drill 2 new holes and bolt our new UHMW shoes
which are the length of the pushers side panel.
Our UHMW shoes are double sided and will last a long time
No more surface abrasion when the pusher is on the pavement. Our UHMW shoes glide along the pavement quietly.
Please contact us with any questions or more more details. We are pleased to provide them.
Thank you for considering our products.
Includes FREE Ground Shipping in the Lower 48 States
If you have the Frontier brand, Front End Loader Mounted Snow Pusher, Model AS10H this listing is for the rubber wear edge on the pushers. Our Rubber Edge is a replacement to the rubber edge which came in the pusher when new.
This pusher is made in the 72” width, 84” width and the 96” width. Our rubber edge replaces the original rubber wear edge on the back of the snow pusher.
The rubber edge is professionally machined with vertical adjustment slots to perfectly align with the mounting holes on the pushers cutting edge location.
This precise machining provides for an easy replacement of the worn main rubber wear edge, to assure the installation, periodic adjustment and ultimate flipping over of the rubber edge is trouble free, to extend the edges useful wear life.
Provides double the wear life by being two sided so it can be flipped over for an entirely new wear edge on the other side.
Contains a full set of corrosion resistant mounting hardware, which are the carriage bolts, the flat washers and the locking nuts to make the installation much easier.
The corrosion resistant hardware makes the periodic adjustments as well as the reversing and flipping over of the main rubber edge easier to complete during use.
Installation Instructions.
The following are the listed weights for the rubber edge which Deere sells for this snow pusher’
72” x 8” x 1” main rubber wear edge weighs 19 pounds
84” x 8” x 1” main rubber wear edge weighs 23 pounds
96” x 8” x 1” main rubber wear edge weighs 26 pounds
Look at how our SBS, LLC plow rubber of the same width and same thickness compares to the Deere Rubber plow edge
72” x 8” x 1” SBS Plow Rubber edge weighs 35 pounds(+16 pounds)
84” x 8” x 1” SBS Plow Rubber Edge weighs 40 pounds(+17 pounds)
96” × 8” x1” SBS Plow Rubber Edge weighs 45 pounds(+19 pounds)
Guess which edge will last longer and work better? Yes, the rubber edge which is more dense, has more mass and greater wear duration and which weighs nearly 50% more. Our Rubber edge.
Now, lets look at the cost difference for the same rubber. We will provide you the Deere part numbers, so you can double check if you like to verify the cost information.
72” Plow Rubber, Deere 5FP1352539, $ 447.75 SBS Price $ 385
84” Plow Rubber, Deere 5FP1352538, $ 566.48 SBS Price $ 485
96” Plow Rubber, Deere 5FP1352467, $ 688.64 SBS Price $ 585
This makes the decision.
Our SBS Snow Pusher Rubber Weighs more (a lot more) so it will last longer. And it costs less, a lot less. Plus our Rubber wear edge includes all new Corrosion Resistant hardware to install the edge, Deere’s is sold at an extra cost. Why pay more and get less?
If you do want to change from the Rubber edge on the snow pusher to a UHMW wear edge, we make that as well. That’s a choice which Deere Doesn’t offer……
We use a very dense rubber product for our plow edges, which we have used for years. Our plow edge wears very well and lasts a long time and cleans the pavement very nicely. In fact, its the best plow rubber material we have found.
Our Rubber edges Ship with a complete set of Corrosion Resistant Hardware, to make installation easy so you aren’t dealing with using old bolts. Our hardware is included in our price, as is our Ground Delivery shipping.
Precision machined for perfect fit, high grade rubber for extended wear life, this back drag rubber restores the function of your snow pushers back drag arm to like new.
Rubber Wear Edge Mounting Straps are available.
We also make the mounting strap to secure the rubber edge, if your metal strap is rusty, damaged, etc. Just make sure to add the strap option to your order to fit the size of your plow blade.
Upgrade to a UHMW Wear Bar and Scrape Hard pack and Ice
If your snow clearing with your AS10H Snow pusher finds you dealing with hard packed snow and ice, you should consider replacing that rubber edge with the UHMW edge. Will scrap like steel, without the noise or abrasion damage. The UHMW wear edges, when used correctly, will last as long or longer than the Mild Steel Option which normally ships on the snow pushers.
The UHMW is often said “Wears like steel, without damage, noise and problems”. The UHMW wear edge won’t harm the pavement. If you need some more “bite” in your snow clearing, but don’t want to destroy the surface in the process. UHMW is your answer.
Our UHMW edge is 1.25” thick and 8” tall. It’s the width of your plow at either 72”, 84” or 96”. We ship our new UHMW wear edges fully cut on the water jet and ready to install with our vertical mounting slots and the edge is cut to length. Don’t buy a project you need to cut and drill to make it fit. Get an edge professionally machined and ready to install in a matter of minutes. Our UHMW Edge includes our Corrosion Resistant Hardware set to complete the installation.
Installation Time Estimates
To replace the rubber wear edge in the snow pusher typically takes 20 to 30 minutes. Installing our new edge is easier thanks to the new hardware as well as the manner in which we machine the installation slots in the rubber edge. Whether installing our new Rubber Replacement edge or our UHMW wear edge, expect the total time to be between 20 and 45 minutes in total. Make sure to follow all safety precautions. Remember, these are only estimates and work conditions, tools, mechanical skill and other factors all impact these results.
Replace those Steel Shoes damaging your driveway pavement
One last item for your consideration. If you would like to end the surface abrasion of the steel shoes on the Deere AS10H snow pusher, we make a complete set of UHMW Shoes for the Deere Snow pusher.
Our new snow pusher UHMW shoes require the removal of the existing shoes. You would have to remove the steel shoes on your pusher, which are going to have to be cut off the pusher housing with either a cutting wheel, plasma cutter or 90 degree grinder. Once the steel shoes are removed, the new shoes install easily on the ends of the snow pusher housing.
Our new shoes are UHMW and include everything needed to install the UHMW shoes, which won’t damage your driveway or pavement. You may find that there are those who want to purchase your old snow pusher steel shoes to attach to box blades or other such assemblies. Keep that in mind when cutting them off the pusher as they may have value to partially help offset the cost of the new items.
You get the old pusher shoes off the pusher, and
drill 2 new holes and bolt our new UHMW shoes
which are the length of the pushers side panel.
Our UHMW shoes are double sided and will last a long time
No more surface abrasion when the pusher is on the pavement. Our UHMW shoes glide along the pavement quietly.
Please contact us with any questions or more more details. We are pleased to provide them.
Thank you for considering our products.
Includes FREE Ground Shipping in the Lower 48 States
If you have the Frontier brand, Front End Loader Mounted Snow Pusher, Model AS10H this listing is for the rubber wear edge on the pushers. Our Rubber Edge is a replacement to the rubber edge which came in the pusher when new.
This pusher is made in the 72” width, 84” width and the 96” width. Our rubber edge replaces the original rubber wear edge on the back of the snow pusher.
The rubber edge is professionally machined with vertical adjustment slots to perfectly align with the mounting holes on the pushers cutting edge location.
This precise machining provides for an easy replacement of the worn main rubber wear edge, to assure the installation, periodic adjustment and ultimate flipping over of the rubber edge is trouble free, to extend the edges useful wear life.
Provides double the wear life by being two sided so it can be flipped over for an entirely new wear edge on the other side.
Contains a full set of corrosion resistant mounting hardware, which are the carriage bolts, the flat washers and the locking nuts to make the installation much easier.
The corrosion resistant hardware makes the periodic adjustments as well as the reversing and flipping over of the main rubber edge easier to complete during use.
Installation Instructions.
The following are the listed weights for the rubber edge which Deere sells for this snow pusher’
72” x 8” x 1” main rubber wear edge weighs 19 pounds
84” x 8” x 1” main rubber wear edge weighs 23 pounds
96” x 8” x 1” main rubber wear edge weighs 26 pounds
Look at how our SBS, LLC plow rubber of the same width and same thickness compares to the Deere Rubber plow edge
72” x 8” x 1” SBS Plow Rubber edge weighs 35 pounds(+16 pounds)
84” x 8” x 1” SBS Plow Rubber Edge weighs 40 pounds(+17 pounds)
96” × 8” x1” SBS Plow Rubber Edge weighs 45 pounds(+19 pounds)
Guess which edge will last longer and work better? Yes, the rubber edge which is more dense, has more mass and greater wear duration and which weighs nearly 50% more. Our Rubber edge.
Now, lets look at the cost difference for the same rubber. We will provide you the Deere part numbers, so you can double check if you like to verify the cost information.
72” Plow Rubber, Deere 5FP1352539, $ 447.75 SBS Price $ 385
84” Plow Rubber, Deere 5FP1352538, $ 566.48 SBS Price $ 485
96” Plow Rubber, Deere 5FP1352467, $ 688.64 SBS Price $ 585
This makes the decision.
Our SBS Snow Pusher Rubber Weighs more (a lot more) so it will last longer. And it costs less, a lot less. Plus our Rubber wear edge includes all new Corrosion Resistant hardware to install the edge, Deere’s is sold at an extra cost. Why pay more and get less?
If you do want to change from the Rubber edge on the snow pusher to a UHMW wear edge, we make that as well. That’s a choice which Deere Doesn’t offer……
We use a very dense rubber product for our plow edges, which we have used for years. Our plow edge wears very well and lasts a long time and cleans the pavement very nicely. In fact, its the best plow rubber material we have found.
Our Rubber edges Ship with a complete set of Corrosion Resistant Hardware, to make installation easy so you aren’t dealing with using old bolts. Our hardware is included in our price, as is our Ground Delivery shipping.
Precision machined for perfect fit, high grade rubber for extended wear life, this back drag rubber restores the function of your snow pushers back drag arm to like new.
Rubber Wear Edge Mounting Straps are available.
We also make the mounting strap to secure the rubber edge, if your metal strap is rusty, damaged, etc. Just make sure to add the strap option to your order to fit the size of your plow blade.
Upgrade to a UHMW Wear Bar and Scrape Hard pack and Ice
If your snow clearing with your AS10H Snow pusher finds you dealing with hard packed snow and ice, you should consider replacing that rubber edge with the UHMW edge. Will scrap like steel, without the noise or abrasion damage. The UHMW wear edges, when used correctly, will last as long or longer than the Mild Steel Option which normally ships on the snow pushers.
The UHMW is often said “Wears like steel, without damage, noise and problems”. The UHMW wear edge won’t harm the pavement. If you need some more “bite” in your snow clearing, but don’t want to destroy the surface in the process. UHMW is your answer.
Our UHMW edge is 1.25” thick and 8” tall. It’s the width of your plow at either 72”, 84” or 96”. We ship our new UHMW wear edges fully cut on the water jet and ready to install with our vertical mounting slots and the edge is cut to length. Don’t buy a project you need to cut and drill to make it fit. Get an edge professionally machined and ready to install in a matter of minutes. Our UHMW Edge includes our Corrosion Resistant Hardware set to complete the installation.
Installation Time Estimates
To replace the rubber wear edge in the snow pusher typically takes 20 to 30 minutes. Installing our new edge is easier thanks to the new hardware as well as the manner in which we machine the installation slots in the rubber edge. Whether installing our new Rubber Replacement edge or our UHMW wear edge, expect the total time to be between 20 and 45 minutes in total. Make sure to follow all safety precautions. Remember, these are only estimates and work conditions, tools, mechanical skill and other factors all impact these results.
Replace those Steel Shoes damaging your driveway pavement
One last item for your consideration. If you would like to end the surface abrasion of the steel shoes on the Deere AS10H snow pusher, we make a complete set of UHMW Shoes for the Deere Snow pusher.
Our new snow pusher UHMW shoes require the removal of the existing shoes. You would have to remove the steel shoes on your pusher, which are going to have to be cut off the pusher housing with either a cutting wheel, plasma cutter or 90 degree grinder. Once the steel shoes are removed, the new shoes install easily on the ends of the snow pusher housing.
Our new shoes are UHMW and include everything needed to install the UHMW shoes, which won’t damage your driveway or pavement. You may find that there are those who want to purchase your old snow pusher steel shoes to attach to box blades or other such assemblies. Keep that in mind when cutting them off the pusher as they may have value to partially help offset the cost of the new items.
You get the old pusher shoes off the pusher, and
drill 2 new holes and bolt our new UHMW shoes
which are the length of the pushers side panel.
Our UHMW shoes are double sided and will last a long time
No more surface abrasion when the pusher is on the pavement. Our UHMW shoes glide along the pavement quietly.
Please contact us with any questions or more more details. We are pleased to provide them.
Thank you for considering our products.
Due to the somewhat rare nature of the Frontier AS10H snow pusher models, we make these parts when ordered. Once your order is received, the part will be placed in our production cue for an order to make the components. Please allow 10 to 15 business days for the item to ship. We will notify you at the time of your order regarding the shipment and order status. We will keep you updated and advise you of the date the kit is shipped and provide you with the shipping tracking numbers. Thank you for your interest in our products.