John Deere QH Snow Blower UHMW Wear Bars Kit
Includes Free Ground Shipping
in the Lower 48 States.
This is our extremely popular UHMW wear bar enhancement part for the Deere Standard duty, Quick Hitch Snowblowers which mount on the front Quik Tach Hitch . Replaces the following Deere Part numbers
M135649 for the 47” Quick Hitch Blower
M161359 for the 54” Deere Quick Hitch Blower.
Our customers report a remarkable transformation in their front mounted snowblower. Here are the benefits of replacing the steel snowblower wear bars with our UHMW Wear bar.
No more pavement scraping, no pavement scratching or surface damage to concrete, asphalt, etc..
Low friction, our blowers push much easier and are quieter on the surface.
They respond more favorably to steering and fight the tractor less.
These wear bars make the blower better balanced front to rear, so they clear the snow better since the blowers are flat on the pavement.
When used with our UHMW snowblower shoes, our blowers are more stable, better balanced, clear snow better and avoid the rust and damage to the pavement.
If you are unsure if this wear bar fits your snowblower, please use our “Contact us” form and send me a picture of the front of your blower and also if possible, the bar coded machine serial number tag. The tag is often near where the hitch connects the blower to the hitch. Thank You.
This wear bar is wider, thicker than the OEM steel bar it replaces, but it fits on your blower without any issues. Installs with our detailed step by step instructions and includes our complete Marine Grade Stainless Hardware set to complete the installation. Make sure to look through our photos as we show our UHMW wear bar, a new “U” shaped wear bar from Deere and the worn steel wear bar off the blower shown in one images side by side. It shows how dramatically different our wear bars are compared to the OEM steel wear bars. It also shows how much thicker our UHMW wear bars is than the steel.
Common Questions about this SBS UHMW Wear bar…..
Q. - How does the SBS UHMW wear bar compare to mild steel wear bar it replaces in terms of dimensions, etc.?
A. - The mild steel “U” shaped wear bar is 3/4” tall and about 3” front to back. The blower rides on two 1/8” steel edges on the steel wear bar. After the steel wear bar has worn down about 3/8”, the mounting hardware starts to grind on the pavement.
Our SBS UHMW wear bar is 1.25” thick, which is 1/2” thicker than the mild steel wear bar. Our wear bars are 3” to 3.5” wide. Our wear bar has to wear 3/4” to reach our recessed hardware. In all likelihood, our UHMW wear bar will outlast the mild steel wear bar it replaced. Our customers report excellent wear characteristics
Q. - What is the main reason so many snowblower owners are switching to the SBS UHMW Snowblower wear bar?
A. - To prevent the scraping, scratching damage and rust which the steel does to the pavement. And our customers are very pleased with the results and dramatic difference it makes. Homeowners who want to avoid damage to their pavement surfaces make the SBS snowblower wear bar their choice.
Q. - How hard is it to replace on my snowblower?
A. - It’s straight forward and not difficult, especially if your snowblower is newer and has had less than 50 hours of use. In most cases, it takes about 30 to 60 minutes, depending upon your mechanical skills, tools, etc.
Q. - What tools do I need to replace this wear bar on my front mounted snowblower?
A. - Basic hand tools including a ratchet and Metric socket (10mm in most cases) and ratchet to remove the hardware. If the bolts are worn down from excessive wear, you may need to use a 90 degree grinder to remove the worn and rusty bolts. This is why the difference between 30 and 60 minutes, it takes longer if you have to grind off old bolts.
Q. - Do I have to remove the blower from my tractor to install this new bar?
A.- It’s easiest and safest to replace this wear bar by tipping the blower forward to make access to the wear bar as easy as possible.
Q. - Being UHMW, how long do you expect these snowblower wear bars to last?
A. - When used correctly and avoiding unnecessary down pressure, the wear bars should last as long and very likely will outlast the mild steel wear bars they replace. In fact, since our UHMW wear bar is much larger than the steel wear bars they replace, the UHMW wear bars will last several seasons of typical residential use and avoiding excessive down pressure.
Q. - Is the UHMW strong enough to be used in this manner?
A. - Absolutely. The UHMW is very durable, in fact, its less prone to damage than the mild steel wear bar it replaces. UHMW replace steel snowplow edges for the same reason, to prevent pavement damage. We also make the UHMW plow edges.
Q.- Why don’t manufacturers put this type of wear bar on the blowers when new to help avoid the damage to driveway pavement surfaces, etc.?
A. - Our UHMW wear bar is expensive to produce and requires 7 different machining processes to make. The UHMW material is about 10x the cost of the mild steel used by the manufacturers. Also, the more mild steel blower wear bars you wear out, the more you have to purchase from Deere.
We also make steel wear bars, but our preference is to avoid the pavement damage steel causes and personally, I use all UHMW. However, if a customer wants to buy a steel wear bar from us, we will produce it for them.
Q. - What do the Deere dealers say about the SBS wear bar?
A. - They like it, as we have many dealers as customers who put our UHMW wear bars on their own Deere snowblowers to avoid the damage to the pavement. We have several dealers who are selling our UHMW wear bars to their blower customers and new dealers contact us weekly. We have customers who own groups of Deere dealerships and they use our UHMW wear bar on their own snowblowers at home and offer them to their customers.
A few more facts about our UHMW Quick Hitch Snowblower wear bars
Our Quick Hitch 47” UHMW wear bar pefectly replaces Deere part number M135649.
Our Quick Hitch 54” UHMW wear bar perfectly replaces Deere part number M161359.
Our wearbar fits on the Deere blower just as the steel bar it replaces.
The SBS UHMW wear bar includes stainless steel corrosion resistant hardware for proper installation.
The SBS UHMW wear bar is wider front to rear and taller than the Deere OEM wear bar. This is by design to get the maximum wear life from this product.
Between this wear edge and the SBS UHMW or RUBBER blower housing shoes, these components protect the blower against wear and eliminate pavement abrasion and wear damage.
This part is made from UHMW material which is highly abrasion resistant and intended to be used in high wear environments.
Our edge is made to be used with our UHMW Blower Shoes for enhanced performance and complete protection from steel surfaces damaging the driveway.
Shipped in a single length unit, ready to be installed. Designed to help stabilize the blower during use and also to help optimize pavement clearing.
Use this link if you are buying the snow blower wear bar and shoes together and get a 10% discount off the combined order. Thank you for your interest in our products.
Thank you for your interest in our products. Should you have any questions, please use our “Contact Us” form and we will get back to you.
Includes Free Ground Shipping
in the Lower 48 States.
This is our extremely popular UHMW wear bar enhancement part for the Deere Standard duty, Quick Hitch Snowblowers which mount on the front Quik Tach Hitch . Replaces the following Deere Part numbers
M135649 for the 47” Quick Hitch Blower
M161359 for the 54” Deere Quick Hitch Blower.
Our customers report a remarkable transformation in their front mounted snowblower. Here are the benefits of replacing the steel snowblower wear bars with our UHMW Wear bar.
No more pavement scraping, no pavement scratching or surface damage to concrete, asphalt, etc..
Low friction, our blowers push much easier and are quieter on the surface.
They respond more favorably to steering and fight the tractor less.
These wear bars make the blower better balanced front to rear, so they clear the snow better since the blowers are flat on the pavement.
When used with our UHMW snowblower shoes, our blowers are more stable, better balanced, clear snow better and avoid the rust and damage to the pavement.
If you are unsure if this wear bar fits your snowblower, please use our “Contact us” form and send me a picture of the front of your blower and also if possible, the bar coded machine serial number tag. The tag is often near where the hitch connects the blower to the hitch. Thank You.
This wear bar is wider, thicker than the OEM steel bar it replaces, but it fits on your blower without any issues. Installs with our detailed step by step instructions and includes our complete Marine Grade Stainless Hardware set to complete the installation. Make sure to look through our photos as we show our UHMW wear bar, a new “U” shaped wear bar from Deere and the worn steel wear bar off the blower shown in one images side by side. It shows how dramatically different our wear bars are compared to the OEM steel wear bars. It also shows how much thicker our UHMW wear bars is than the steel.
Common Questions about this SBS UHMW Wear bar…..
Q. - How does the SBS UHMW wear bar compare to mild steel wear bar it replaces in terms of dimensions, etc.?
A. - The mild steel “U” shaped wear bar is 3/4” tall and about 3” front to back. The blower rides on two 1/8” steel edges on the steel wear bar. After the steel wear bar has worn down about 3/8”, the mounting hardware starts to grind on the pavement.
Our SBS UHMW wear bar is 1.25” thick, which is 1/2” thicker than the mild steel wear bar. Our wear bars are 3” to 3.5” wide. Our wear bar has to wear 3/4” to reach our recessed hardware. In all likelihood, our UHMW wear bar will outlast the mild steel wear bar it replaced. Our customers report excellent wear characteristics
Q. - What is the main reason so many snowblower owners are switching to the SBS UHMW Snowblower wear bar?
A. - To prevent the scraping, scratching damage and rust which the steel does to the pavement. And our customers are very pleased with the results and dramatic difference it makes. Homeowners who want to avoid damage to their pavement surfaces make the SBS snowblower wear bar their choice.
Q. - How hard is it to replace on my snowblower?
A. - It’s straight forward and not difficult, especially if your snowblower is newer and has had less than 50 hours of use. In most cases, it takes about 30 to 60 minutes, depending upon your mechanical skills, tools, etc.
Q. - What tools do I need to replace this wear bar on my front mounted snowblower?
A. - Basic hand tools including a ratchet and Metric socket (10mm in most cases) and ratchet to remove the hardware. If the bolts are worn down from excessive wear, you may need to use a 90 degree grinder to remove the worn and rusty bolts. This is why the difference between 30 and 60 minutes, it takes longer if you have to grind off old bolts.
Q. - Do I have to remove the blower from my tractor to install this new bar?
A.- It’s easiest and safest to replace this wear bar by tipping the blower forward to make access to the wear bar as easy as possible.
Q. - Being UHMW, how long do you expect these snowblower wear bars to last?
A. - When used correctly and avoiding unnecessary down pressure, the wear bars should last as long and very likely will outlast the mild steel wear bars they replace. In fact, since our UHMW wear bar is much larger than the steel wear bars they replace, the UHMW wear bars will last several seasons of typical residential use and avoiding excessive down pressure.
Q. - Is the UHMW strong enough to be used in this manner?
A. - Absolutely. The UHMW is very durable, in fact, its less prone to damage than the mild steel wear bar it replaces. UHMW replace steel snowplow edges for the same reason, to prevent pavement damage. We also make the UHMW plow edges.
Q.- Why don’t manufacturers put this type of wear bar on the blowers when new to help avoid the damage to driveway pavement surfaces, etc.?
A. - Our UHMW wear bar is expensive to produce and requires 7 different machining processes to make. The UHMW material is about 10x the cost of the mild steel used by the manufacturers. Also, the more mild steel blower wear bars you wear out, the more you have to purchase from Deere.
We also make steel wear bars, but our preference is to avoid the pavement damage steel causes and personally, I use all UHMW. However, if a customer wants to buy a steel wear bar from us, we will produce it for them.
Q. - What do the Deere dealers say about the SBS wear bar?
A. - They like it, as we have many dealers as customers who put our UHMW wear bars on their own Deere snowblowers to avoid the damage to the pavement. We have several dealers who are selling our UHMW wear bars to their blower customers and new dealers contact us weekly. We have customers who own groups of Deere dealerships and they use our UHMW wear bar on their own snowblowers at home and offer them to their customers.
A few more facts about our UHMW Quick Hitch Snowblower wear bars
Our Quick Hitch 47” UHMW wear bar pefectly replaces Deere part number M135649.
Our Quick Hitch 54” UHMW wear bar perfectly replaces Deere part number M161359.
Our wearbar fits on the Deere blower just as the steel bar it replaces.
The SBS UHMW wear bar includes stainless steel corrosion resistant hardware for proper installation.
The SBS UHMW wear bar is wider front to rear and taller than the Deere OEM wear bar. This is by design to get the maximum wear life from this product.
Between this wear edge and the SBS UHMW or RUBBER blower housing shoes, these components protect the blower against wear and eliminate pavement abrasion and wear damage.
This part is made from UHMW material which is highly abrasion resistant and intended to be used in high wear environments.
Our edge is made to be used with our UHMW Blower Shoes for enhanced performance and complete protection from steel surfaces damaging the driveway.
Shipped in a single length unit, ready to be installed. Designed to help stabilize the blower during use and also to help optimize pavement clearing.
Use this link if you are buying the snow blower wear bar and shoes together and get a 10% discount off the combined order. Thank you for your interest in our products.
Thank you for your interest in our products. Should you have any questions, please use our “Contact Us” form and we will get back to you.
Includes Free Ground Shipping
in the Lower 48 States.
This is our extremely popular UHMW wear bar enhancement part for the Deere Standard duty, Quick Hitch Snowblowers which mount on the front Quik Tach Hitch . Replaces the following Deere Part numbers
M135649 for the 47” Quick Hitch Blower
M161359 for the 54” Deere Quick Hitch Blower.
Our customers report a remarkable transformation in their front mounted snowblower. Here are the benefits of replacing the steel snowblower wear bars with our UHMW Wear bar.
No more pavement scraping, no pavement scratching or surface damage to concrete, asphalt, etc..
Low friction, our blowers push much easier and are quieter on the surface.
They respond more favorably to steering and fight the tractor less.
These wear bars make the blower better balanced front to rear, so they clear the snow better since the blowers are flat on the pavement.
When used with our UHMW snowblower shoes, our blowers are more stable, better balanced, clear snow better and avoid the rust and damage to the pavement.
If you are unsure if this wear bar fits your snowblower, please use our “Contact us” form and send me a picture of the front of your blower and also if possible, the bar coded machine serial number tag. The tag is often near where the hitch connects the blower to the hitch. Thank You.
This wear bar is wider, thicker than the OEM steel bar it replaces, but it fits on your blower without any issues. Installs with our detailed step by step instructions and includes our complete Marine Grade Stainless Hardware set to complete the installation. Make sure to look through our photos as we show our UHMW wear bar, a new “U” shaped wear bar from Deere and the worn steel wear bar off the blower shown in one images side by side. It shows how dramatically different our wear bars are compared to the OEM steel wear bars. It also shows how much thicker our UHMW wear bars is than the steel.
Common Questions about this SBS UHMW Wear bar…..
Q. - How does the SBS UHMW wear bar compare to mild steel wear bar it replaces in terms of dimensions, etc.?
A. - The mild steel “U” shaped wear bar is 3/4” tall and about 3” front to back. The blower rides on two 1/8” steel edges on the steel wear bar. After the steel wear bar has worn down about 3/8”, the mounting hardware starts to grind on the pavement.
Our SBS UHMW wear bar is 1.25” thick, which is 1/2” thicker than the mild steel wear bar. Our wear bars are 3” to 3.5” wide. Our wear bar has to wear 3/4” to reach our recessed hardware. In all likelihood, our UHMW wear bar will outlast the mild steel wear bar it replaced. Our customers report excellent wear characteristics
Q. - What is the main reason so many snowblower owners are switching to the SBS UHMW Snowblower wear bar?
A. - To prevent the scraping, scratching damage and rust which the steel does to the pavement. And our customers are very pleased with the results and dramatic difference it makes. Homeowners who want to avoid damage to their pavement surfaces make the SBS snowblower wear bar their choice.
Q. - How hard is it to replace on my snowblower?
A. - It’s straight forward and not difficult, especially if your snowblower is newer and has had less than 50 hours of use. In most cases, it takes about 30 to 60 minutes, depending upon your mechanical skills, tools, etc.
Q. - What tools do I need to replace this wear bar on my front mounted snowblower?
A. - Basic hand tools including a ratchet and Metric socket (10mm in most cases) and ratchet to remove the hardware. If the bolts are worn down from excessive wear, you may need to use a 90 degree grinder to remove the worn and rusty bolts. This is why the difference between 30 and 60 minutes, it takes longer if you have to grind off old bolts.
Q. - Do I have to remove the blower from my tractor to install this new bar?
A.- It’s easiest and safest to replace this wear bar by tipping the blower forward to make access to the wear bar as easy as possible.
Q. - Being UHMW, how long do you expect these snowblower wear bars to last?
A. - When used correctly and avoiding unnecessary down pressure, the wear bars should last as long and very likely will outlast the mild steel wear bars they replace. In fact, since our UHMW wear bar is much larger than the steel wear bars they replace, the UHMW wear bars will last several seasons of typical residential use and avoiding excessive down pressure.
Q. - Is the UHMW strong enough to be used in this manner?
A. - Absolutely. The UHMW is very durable, in fact, its less prone to damage than the mild steel wear bar it replaces. UHMW replace steel snowplow edges for the same reason, to prevent pavement damage. We also make the UHMW plow edges.
Q.- Why don’t manufacturers put this type of wear bar on the blowers when new to help avoid the damage to driveway pavement surfaces, etc.?
A. - Our UHMW wear bar is expensive to produce and requires 7 different machining processes to make. The UHMW material is about 10x the cost of the mild steel used by the manufacturers. Also, the more mild steel blower wear bars you wear out, the more you have to purchase from Deere.
We also make steel wear bars, but our preference is to avoid the pavement damage steel causes and personally, I use all UHMW. However, if a customer wants to buy a steel wear bar from us, we will produce it for them.
Q. - What do the Deere dealers say about the SBS wear bar?
A. - They like it, as we have many dealers as customers who put our UHMW wear bars on their own Deere snowblowers to avoid the damage to the pavement. We have several dealers who are selling our UHMW wear bars to their blower customers and new dealers contact us weekly. We have customers who own groups of Deere dealerships and they use our UHMW wear bar on their own snowblowers at home and offer them to their customers.
A few more facts about our UHMW Quick Hitch Snowblower wear bars
Our Quick Hitch 47” UHMW wear bar pefectly replaces Deere part number M135649.
Our Quick Hitch 54” UHMW wear bar perfectly replaces Deere part number M161359.
Our wearbar fits on the Deere blower just as the steel bar it replaces.
The SBS UHMW wear bar includes stainless steel corrosion resistant hardware for proper installation.
The SBS UHMW wear bar is wider front to rear and taller than the Deere OEM wear bar. This is by design to get the maximum wear life from this product.
Between this wear edge and the SBS UHMW or RUBBER blower housing shoes, these components protect the blower against wear and eliminate pavement abrasion and wear damage.
This part is made from UHMW material which is highly abrasion resistant and intended to be used in high wear environments.
Our edge is made to be used with our UHMW Blower Shoes for enhanced performance and complete protection from steel surfaces damaging the driveway.
Shipped in a single length unit, ready to be installed. Designed to help stabilize the blower during use and also to help optimize pavement clearing.
Use this link if you are buying the snow blower wear bar and shoes together and get a 10% discount off the combined order. Thank you for your interest in our products.
Thank you for your interest in our products. Should you have any questions, please use our “Contact Us” form and we will get back to you.
Many of our items are kept in stock much of the year. As seasonal demand increases we produce additional parts trying to maintain the proper inventory levels. At times, we are temporarily out of stock on some items. Should this happenm we will advise you of the estimated shipping date of your order when your order is placed. We will update you during the production period of any change in the estimated shipping date. Once your order ships, you will be provided the shipping tracking numbers and an expected delivery date. Thank you for your interest in our products. We sincerely appreciate it.