John Deere 60" Heavy Duty Snow Thrower Wear Bar M142890, Our Edge is UHMW
Includes Free Ground Shipping
in the Lower 48 States.
This product will protect your pavement against the damage caused by the steel wear bars which come on the snowblower when new.
If you have John Deere’s Biggest, Baddest Front Mounted Snowblower, you should also have the UHMW edge which protects your pavement against wear and damage from the metal wear edge on the pavement. This is your snowblower edge…….
This part is for the Heavy Duty 60" Deere Snowblowers. Replaces Deere Part number M142890.
The Deere wear bar on your blower is steel. It grinds on the pavement with every pass the blower makes. Our wear edge is made of UHMW which is a very special wear resistant plastic material. Ultra High Molecular Weight plastic is the most wear resistant plastic product produced.
Used properly, this wear edge will last for seasons of typical residential use*
Our wear edge provides two complete wear surfaces. When one side is worn, flip over the edge and have another entire wear bar on the other side.
This edge is FLAT in shape and mounted where it can be seen when you look in the front of the blower housing.
One of our images shows the location of the wear bar with the white arrows inside of the 60 HD Blower.
The flat style wear bar is used on all Heavy Duty Deere blowers.
This wear bar measures 58.43" long, or 1,484mm. Deere calls the length 58.5 inches for their 60” wide blower.
Our Blower wear bar is wider and thicker than the Deere wear bar. Our Our edge mounts using the center holes in the wear bar.
There are groups of 3 holes shown in the images of the blower wear bar for the HD blowers. The center hole with the red arrow is the mounting hole, the two outer holes in each row with the yellow arrows are wear indicator holes.
These wear indicators allow the owner to monitor the wear condition of the wear bar.
When the blower wear holes shown with the yellow arrows in the image are visible from the front of the blower, its time to flip over the wear edge.
Our UHMW wear edge is custom made to replace the John Deere Steel wear bar which fits on the bottom of the Heavy Duty Deere 60" snowblower. This part is a crucial wear bar to protect the snow blower housing against the surface wear which occurs as the blower is pushed across the pavement.
If you are unsure if these wear bar or shoes will fit your blower, please send me a message at the “Contact us” form and if possible, include either the machine tag off your blower or pictures of the front of your blower and I can determine which blower shoes or wear bar is right for your machine.. Thank you…..
This part is made from UHMW material which is highly abrasion resistant and intended to be used in high wear environments. Our edge is made to be used with our UHMW Blower Shoes which protect the the pavement as well.
Use the special order of the listing ‘UHMW Blower Wear Bar and Shoes, what you need to know” and get 10% off the combined order of wear bar and shoes.
Made to bolt right in the same location as the steel wear bar sold under Deere part number M142890. Includes proper hardware to install this new wear edge correctly. The hardware is stainless steel to tolerate snow melt and other seasonal corrosion. This is the best hardware available to prevent rust and corrosion.
Shipped in a single length unit, ready to be installed. Due to its length, this is an oversized item for shipping and we are paying the extra costs to ship it in one piece, so its stronger and a better edge.
Don’t be tempted by wear edges which are cut into shorter pieces to reduce the shipping costs as the seams in the wear bars are not as strong as our one piece wear bar.
Designed to help stabilize the blower during use and also to help optimize pavement clearing.
Includes Free Ground Shipping
in the Lower 48 States.
This product will protect your pavement against the damage caused by the steel wear bars which come on the snowblower when new.
If you have John Deere’s Biggest, Baddest Front Mounted Snowblower, you should also have the UHMW edge which protects your pavement against wear and damage from the metal wear edge on the pavement. This is your snowblower edge…….
This part is for the Heavy Duty 60" Deere Snowblowers. Replaces Deere Part number M142890.
The Deere wear bar on your blower is steel. It grinds on the pavement with every pass the blower makes. Our wear edge is made of UHMW which is a very special wear resistant plastic material. Ultra High Molecular Weight plastic is the most wear resistant plastic product produced.
Used properly, this wear edge will last for seasons of typical residential use*
Our wear edge provides two complete wear surfaces. When one side is worn, flip over the edge and have another entire wear bar on the other side.
This edge is FLAT in shape and mounted where it can be seen when you look in the front of the blower housing.
One of our images shows the location of the wear bar with the white arrows inside of the 60 HD Blower.
The flat style wear bar is used on all Heavy Duty Deere blowers.
This wear bar measures 58.43" long, or 1,484mm. Deere calls the length 58.5 inches for their 60” wide blower.
Our Blower wear bar is wider and thicker than the Deere wear bar. Our Our edge mounts using the center holes in the wear bar.
There are groups of 3 holes shown in the images of the blower wear bar for the HD blowers. The center hole with the red arrow is the mounting hole, the two outer holes in each row with the yellow arrows are wear indicator holes.
These wear indicators allow the owner to monitor the wear condition of the wear bar.
When the blower wear holes shown with the yellow arrows in the image are visible from the front of the blower, its time to flip over the wear edge.
Our UHMW wear edge is custom made to replace the John Deere Steel wear bar which fits on the bottom of the Heavy Duty Deere 60" snowblower. This part is a crucial wear bar to protect the snow blower housing against the surface wear which occurs as the blower is pushed across the pavement.
If you are unsure if these wear bar or shoes will fit your blower, please send me a message at the “Contact us” form and if possible, include either the machine tag off your blower or pictures of the front of your blower and I can determine which blower shoes or wear bar is right for your machine.. Thank you…..
This part is made from UHMW material which is highly abrasion resistant and intended to be used in high wear environments. Our edge is made to be used with our UHMW Blower Shoes which protect the the pavement as well.
Use the special order of the listing ‘UHMW Blower Wear Bar and Shoes, what you need to know” and get 10% off the combined order of wear bar and shoes.
Made to bolt right in the same location as the steel wear bar sold under Deere part number M142890. Includes proper hardware to install this new wear edge correctly. The hardware is stainless steel to tolerate snow melt and other seasonal corrosion. This is the best hardware available to prevent rust and corrosion.
Shipped in a single length unit, ready to be installed. Due to its length, this is an oversized item for shipping and we are paying the extra costs to ship it in one piece, so its stronger and a better edge.
Don’t be tempted by wear edges which are cut into shorter pieces to reduce the shipping costs as the seams in the wear bars are not as strong as our one piece wear bar.
Designed to help stabilize the blower during use and also to help optimize pavement clearing.
Includes Free Ground Shipping
in the Lower 48 States.
This product will protect your pavement against the damage caused by the steel wear bars which come on the snowblower when new.
If you have John Deere’s Biggest, Baddest Front Mounted Snowblower, you should also have the UHMW edge which protects your pavement against wear and damage from the metal wear edge on the pavement. This is your snowblower edge…….
This part is for the Heavy Duty 60" Deere Snowblowers. Replaces Deere Part number M142890.
The Deere wear bar on your blower is steel. It grinds on the pavement with every pass the blower makes. Our wear edge is made of UHMW which is a very special wear resistant plastic material. Ultra High Molecular Weight plastic is the most wear resistant plastic product produced.
Used properly, this wear edge will last for seasons of typical residential use*
Our wear edge provides two complete wear surfaces. When one side is worn, flip over the edge and have another entire wear bar on the other side.
This edge is FLAT in shape and mounted where it can be seen when you look in the front of the blower housing.
One of our images shows the location of the wear bar with the white arrows inside of the 60 HD Blower.
The flat style wear bar is used on all Heavy Duty Deere blowers.
This wear bar measures 58.43" long, or 1,484mm. Deere calls the length 58.5 inches for their 60” wide blower.
Our Blower wear bar is wider and thicker than the Deere wear bar. Our Our edge mounts using the center holes in the wear bar.
There are groups of 3 holes shown in the images of the blower wear bar for the HD blowers. The center hole with the red arrow is the mounting hole, the two outer holes in each row with the yellow arrows are wear indicator holes.
These wear indicators allow the owner to monitor the wear condition of the wear bar.
When the blower wear holes shown with the yellow arrows in the image are visible from the front of the blower, its time to flip over the wear edge.
Our UHMW wear edge is custom made to replace the John Deere Steel wear bar which fits on the bottom of the Heavy Duty Deere 60" snowblower. This part is a crucial wear bar to protect the snow blower housing against the surface wear which occurs as the blower is pushed across the pavement.
If you are unsure if these wear bar or shoes will fit your blower, please send me a message at the “Contact us” form and if possible, include either the machine tag off your blower or pictures of the front of your blower and I can determine which blower shoes or wear bar is right for your machine.. Thank you…..
This part is made from UHMW material which is highly abrasion resistant and intended to be used in high wear environments. Our edge is made to be used with our UHMW Blower Shoes which protect the the pavement as well.
Use the special order of the listing ‘UHMW Blower Wear Bar and Shoes, what you need to know” and get 10% off the combined order of wear bar and shoes.
Made to bolt right in the same location as the steel wear bar sold under Deere part number M142890. Includes proper hardware to install this new wear edge correctly. The hardware is stainless steel to tolerate snow melt and other seasonal corrosion. This is the best hardware available to prevent rust and corrosion.
Shipped in a single length unit, ready to be installed. Due to its length, this is an oversized item for shipping and we are paying the extra costs to ship it in one piece, so its stronger and a better edge.
Don’t be tempted by wear edges which are cut into shorter pieces to reduce the shipping costs as the seams in the wear bars are not as strong as our one piece wear bar.
Designed to help stabilize the blower during use and also to help optimize pavement clearing.
Many of our items are kept in stock much of the year. As seasonal demand increases we produce additional parts trying to maintain the proper inventory levels. At times, we are temporarily out of stock on some items. Should this happen we will advise you of the estimated shipping date of your order when your order is placed. We will update you during the production period of any change in the estimated shipping date. Once your order ships, you will be provided the shipping tracking numbers and an expected delivery date. Thank you for your interest in our products. We sincerely appreciate it.